At Garneau Tool, we see it all too often: a perfectly good lawn mower, snow blower, or trimmer is discarded because a small component fails — and the manufacturer either no longer supplies parts or makes repairs deliberately difficult. This is the reality of planned obsolescence, and it’s something we firmly stand against.

We believe in right to repair, in empowering equipment owners, and in showing that older machines — when properly maintained — often outperform brand-new equipment in reliability, durability, and serviceability.

What Is Planned Obsolescence?

Planned obsolescence is the practice of designing products to wear out, fail, or become obsolete sooner than necessary, encouraging consumers to buy replacements. In small engines, this can manifest as:

• Carburetors or fuel systems that are hard or impossible to clean

• Proprietary parts that are extremely expensive or unavailable

• Plastic components that fail prematurely

• Electronics or sensors that prevent a machine from running if a minor fault occurs

The result? Machines that could last decades are pushed into the scrap heap after a few seasons.

Right to Repair: Why It Matters

The right to repair movement is about giving consumers and independent repair shops the ability to service, maintain, and repair their own equipment without being forced to buy new machines.

At Garneau Tool, we fully support this principle. Why? Because:

1. Old machines are often better built

   • Pre-2010 small engines were simpler, with fewer sensors, less proprietary tech, and stronger mechanical components.

   • These machines can often be repaired and returned to reliable service, whereas modern units sometimes fail from a single electronics fault.

2. Repair is environmentally responsible

   • Every machine that can be fixed is one less item in a landfill.

3. Repair saves money for our clients

   • Many customers assume replacement is the only option. We show that cleaning, replacing a gasket, or rebuilding a carb can bring a machine back to peak condition for a fraction of the cost.

Old Machines vs. New Machines

We see a clear bias in the industry toward newer machines. Marketing campaigns push “upgrades” and “latest technology,” but the reality is that many older machines were:

• Built with durable steel components instead of plastic

• Designed to be serviceable by owners or independent technicians

• Simpler to troubleshoot, diagnose, and repair

Contrast this with many modern machines, which:

• Rely on electronic sensors and proprietary software

• Have plastic or sealed components that fail irreparably

• Are extremely difficult for independent shops to service

At Garneau Tool, our technicians prefer the challenge of restoring old machines because they were built to last and can be returned to reliable service with proper care.

Repairing vs. Replacing: Our Philosophy

When a client brings in a machine, our first question is always:

“Can this be repaired effectively, or is replacement truly the only option?”

We believe in repairing whenever possible. That means:

• Ultrasonic carb cleaning

• Replacing gaskets, floats, needles, and other consumables

• Inspecting and restoring fuel tanks

• Adjusting and tuning engines for optimal performance

Replacement is only recommended when:

• The machine is structurally compromised

• Replacement parts are unavailable or unsafe

• Repair costs approach or exceed the cost of a high-quality machine

By repairing, we give machines a second (or third!) life, keep costs down, and reduce waste.

How Garneau Tool Supports Right to Repair

Garneau Tool actively supports the right to repair for all small engines:

• We source parts for older models, even when they’re discontinued elsewhere

• We educate clients on maintenance best practices

• We provide mobile service to help repair machines where they are

• We advise on DIY-friendly repairs for clients who prefer hands-on maintenance

We refuse to push unnecessary replacements — instead, our focus is making older machines run like new.

Why Clients Love Old Machines

Clients often come in thinking their old mower or blower is “done for.” After a thorough inspection and service from Garneau Tool, they’re often surprised by how reliable the equipment becomes.

Benefits of repairing older machines:

• Lower cost than replacement

• Proven durability

• Parts can often be repaired or replaced individually

• Simpler mechanics make troubleshooting easier

• Reduced environmental impact

Final Thoughts

At Garneau Tool, we hate seeing perfectly good machines discarded due to planned obsolescence. We support right to repair, we champion older equipment, and we prioritize repair over replacement whenever possible.

Machines are more than metal and plastic — they’re investments. With proper maintenance, even decades-old equipment can remain reliable, efficient, and ready to work.

If your mower, snow blower, or trimmer is struggling, don’t immediately reach for a replacement. Bring it to Garneau Tool — we’ll revive, repair, and maintain it so it continues working for years to come.